Your browser is not supported anymore.

We suggest changing from Internet Explorer to another option. The Internet Explorer browser is no longer supported by Microsoft. Please install or upgrade one of the browsers below.


Optimization in the quarries, Norwegians show the way

June 10, 2015

Brønnøy Kalk AS, owners of the Akselberg limestone quarry in northern Norway, has achieved consistency and reliability in its production process. This, in turn, has helped to boost efficiency throughout the operation.
The Akselberg quarry in central Norway, about 400 km north of Trondheim, produces about 1.8 million tonnes of limestone carbonate annually, a product widely used in the European paper industry.
Since it was established in 1997, this 2.5 km long and 1.5 km wide pit has consistently improved its productivity in drilling and blasting. Today, however, the Brønnøy team is getting better results than ever due to professional planning and meticulous attention to every step in the production process.
As Raymond Langfjord, Production Manager at the site, explains: “Everything here starts with the drilling. If we get that wrong, it has consequences for every other phase in our operation – from blasting and loading through to crushing and, ultimately, the quality of our products."
SmartROC T45 at Brønnøy Kalk AS quarry
“Our vision has always been to achieve optimal utilization of the limestone here and that requires optimizing the whole excavation process. That’s why we are very happy to be getting top results with our equipment and to see the effect of this on the total efficiency of our operation.”

Precision on the benches

The equipment on site consists of Atlas Copco SmartROC tophammer drill rigs complete with the Hole Navigation System (HNS), AutoPos function and ROC Manager, which creates drill plans and reports. HNS and AutoPos together are key functions that enable the operator to locate and collar the hole with accurate angles, first time every time.

"Everything here starts with the drilling. If we get that wrong, it has consequences for every other phase in our operation – from blasting and loading through to crushing and, ultimately, the quality of our products"

Raymond Langfjord ,Production Manager
There are three rigs at work in the quarry – a SmartRig ROC F9C, a SmartROC T40 and a SmartROC T45 – drilling on 15 m high benches. The holes are drilled at an inclination of 10°. Five rows are drilled with a burden of 2.8 m and a spacing of 3.5 m. After charging and firing, 20 000 to 80 000 tonnes of rock are removed with each blast and the quarry carries out an average of 10 blasts per month.
The rigs use T51 drill rods and 89 mm ballistic button bits from Atlas Copco Secoroc and have no trouble penetrating the overburden. On the contrary, the rock is relatively easy to drill with penetration rates of 1.8 to 2.5 m per minute. The bits only need to be reground every 250 m and, at best, one bit can last for up to 6 000 m.
But if the rock is easy to drill, Langfjord explains that it is more difficult to blast and that parallel holes are vital for success. “We have to make sure that all of the holes are drilled to the right depth and with the right inclination and absolutely parallel,” he says. “In addition, the hole bottoms have to be positioned in exactly the right spot. Any deviation, however small, will undermine the success of the blasted round. And as these rounds are spread out over such a large area, small errors can become big problems.”

The all-important last row

Fortunately, the drillers are able to meet these tough demands using the rigs’ HNS system together with the AutoPos function.
“The last row of holes, which is always at the rear of the bench, is the most important one,” continues Langfjord. “This is the master row and it has to be right. Otherwise it will negatively affect the rest.
“With HNS we can import the drill plan that has been created in ROC Manager, using a USB, and the system helps the operator to navigate the rig to the precise hole location. The rig’s AutoPos function then sets up the correct inclination on the feed, ensuring that the bit will hit the right spot on the ground at the touch of a button. The operator starts drilling and then simply switches to automatic mode and the rig drills the rest of the hole by itself.” In this way, the AutoPos function minimizes the risk of human error. Read the full story at Mining and Construction online.

Epiroc operated under the trademark “Atlas Copco” prior to January 1, 2018.

2015 Quarrying SmartROC T45 International Surface drill rigs Surface and Exploration Drilling division Customer story SmartROC T40

Related stories